Best Headphones for Mixing at Home (2026)

The best studio headphones for mixing in a home studio, open-back and closed-back, compared on impedance, weight, cables and what your interface can drive.

By
Sajime
Published
Reading time
5 min

DisclosureWe may earn a commission when you buy through links on this site, at no extra cost to you. As an Amazon Associate we earn from qualifying purchases.

Our picks at a glance

Our picks at a glance
#ProductBest forRatingLinks
01Sennheiser HD 600Best overall open-back
02Sennheiser HD 490 PROBest for mixing and producing
03beyerdynamic DT 900 PRO XBest open-back for interface outputs
04Audio-Technica ATH-R70xaLightest for long sessions
05beyerdynamic DT 770 PRO (80 ohms)Best closed-back for mixing and tracking
06Audio-Technica ATH-M50xBest closed-back all-rounder
No.1Best overall open-back
Sennheiser

Sennheiser HD 600

A long-running open-back reference for mixing. At 300 ohms it needs a strong headphone output, so check your interface first.

Type
Open-back, over-ear, dynamic
Impedance
300 ohms
Frequency response
12 Hz – 40.5 kHz
No.2Best for mixing and producing
Sennheiser

Sennheiser HD 490 PRO

Open-back headphones made for studio work, with two ear pad sets in the box, one for mixing and one for producing.

Type
Open-back, over-ear, dynamic
Driver
38 mm
Impedance
130 ohms
No.3Best open-back for interface outputs
beyerdynamic

beyerdynamic DT 900 PRO X

At 48 ohms, they're far easier to drive from a typical interface or laptop than most mixing headphones, and the mini-XLR cable is detachable.

Type
Open-back, over-ear, dynamic
Driver
STELLAR.45 dynamic driver
Impedance
48 ohms
No.4Lightest for long sessions
Audio-Technica

Audio-Technica ATH-R70xa

At 199 g without the cable, the lightest pair on this list. The 470-ohm impedance means it needs a capable headphone amp.

Type
Open-back, over-ear, dynamic
Driver
45 mm
Impedance
470 ohms
No.5Best closed-back for mixing and tracking
beyerdynamic

beyerdynamic DT 770 PRO (80 ohms)

One closed-back pair for recording and checking mixes, with replaceable ear pads and an 80-ohm impedance.

Type
Closed-back, over-ear, dynamic
Impedance
80 ohms
Frequency response
5 Hz – 35 kHz
No.6Best closed-back all-rounder
Audio-Technica

Audio-Technica ATH-M50x

Low 38-ohm impedance and three detachable cables in the box. Easy to drive from almost anything.

Type
Closed-back, over-ear, dynamic
Driver
45 mm
Impedance
38 ohms

The best headphones for mixing are usually open-back studio models. Our top pick is the Sennheiser HD 600, as long as your interface can drive its 300 ohms. The Sennheiser HD 490 PRO is made for mixing and producing and comes with two pad sets. The beyerdynamic DT 900 PRO X is the easiest open-back pair here to drive from a typical interface. Do you also record vocals? Then pick a closed-back pair like the beyerdynamic DT 770 PRO or Audio-Technica ATH-M50x, so nothing leaks into the mic.

Quick comparison

Headphones Design Impedance Weight (without cable) Cable
Sennheiser HD 600 Open-back 300 ohms 260 g Detachable, 3 m
Sennheiser HD 490 PRO Open-back 130 ohms About 260 g 1.8 m
beyerdynamic DT 900 PRO X Open-back 48 ohms 345 g Detachable, mini-XLR
Audio-Technica ATH-R70xa Open-back 470 ohms 199 g Detachable, dual-sided, 3 m
beyerdynamic DT 770 PRO (80 ohms) Closed-back 80 ohms 270 g 3 m straight
Audio-Technica ATH-M50x Closed-back 38 ohms 285 g 3 detachable cables

Specs are from each maker’s product page or spec sheet.

What matters in mixing headphones

  • Open or closed. Open-back cups let air and sound pass through. That avoids the pressure build-up of a sealed cup, and it’s why most mixing headphones are open. The catch: they leak both ways, so they’re a poor pick for recording or noisy rooms. Our open-back vs closed-back guide goes into detail.
  • Impedance and your interface. Higher-impedance headphones need more voltage from the headphone output. A low-impedance pair (under about 80 ohms) is the safe choice if you plug straight into a laptop or a small interface. For 300 ohms and up, check your interface’s headphone specs or budget for a headphone amp.
  • Comfort over hours. Mixing sessions are long. Weight and clamping force matter, and replaceable ear pads keep a pair going longer.
  • Detachable cables. A broken cable is the most common failure. If it’s detachable, it’s a cheap fix instead of a new pair.

The picks in detail

Sennheiser HD 600: best overall open-back

The HD 600 is an open-back dynamic headphone that’s been a mixing staple for a long time. Sennheiser lists 300 ohms, a 12 Hz – 40.5 kHz frequency response, 97 dB SPL (at 1 V) and 260 g without the cable. The catch is that impedance. Many small bus-powered interfaces can’t drive it to a comfortable level.

Skip it if you plan to plug straight into a laptop or a basic interface and don’t want to add a headphone amp.

Sennheiser HD 490 PRO: best for mixing and producing

The HD 490 PRO is Sennheiser’s open-back headphone built for studio production. What makes it different is the two ear pad sets in the box. Sennheiser describes the fabric mixing pads as flatter and more neutral, and the velour producing pads as slightly warmer. Both sets are washable and replaceable. Sennheiser lists 130 ohms, 38 mm drivers, 5 Hz – 36 kHz (-10 dB) and about 260 g.

Skip it if you want the easiest pair to drive. The DT 900 PRO X has a lower impedance.

beyerdynamic DT 900 PRO X: best open-back for interface outputs

The DT 900 PRO X is an open-back design built around beyerdynamic’s STELLAR.45 driver. Its 48-ohm impedance is low enough for most interface and laptop headphone outputs. beyerdynamic lists 5 Hz – 40 kHz, 100 dB SPL sensitivity and 345 g without the cable. The cable is detachable with a mini-XLR plug, so it’s easy to replace.

Skip it if weight is your top priority. At 345 g, it’s the heaviest pair here.

Audio-Technica ATH-R70xa: lightest for long sessions

Audio-Technica’s open-back reference headphones weigh 199 g without the cable, the lightest on this list. The trade-off is the 470-ohm impedance. Audio-Technica itself warns that devices like smartphones may not get them loud enough, so plan on a strong headphone output. It also lists 45 mm drivers, 5 Hz – 40 kHz, 97 dB/mW and a detachable dual-sided 3.0 m cable with a bayonet lock.

Skip it if you don’t have, or don’t want, a headphone amp.

beyerdynamic DT 770 PRO (80 ohms): best closed-back for mixing and tracking

If one pair has to handle recording and mixing, go closed-back so nothing leaks into the mic. The DT 770 PRO is the closed sibling of beyerdynamic’s open DT 990 PRO. beyerdynamic lists 80 ohms, 5 Hz – 35 kHz, 96 dB and 270 g without the cable. The ear pads are replaceable, and the 80-ohm version comes with a 3 m straight cable.

Skip it if you only mix and never record. An open-back pair is the better mixing tool.

Audio-Technica ATH-M50x: best closed-back all-rounder

The ATH-M50x is a long-running closed-back studio model. At 38 ohms it’s easy to drive from just about anything, and the box includes three detachable cables (coiled, 3 m straight and 1.2 m straight). Audio-Technica lists 45 mm drivers, 15 Hz – 28 kHz, 99 dB sensitivity and 285 g.

Skip it if mixing is your main job and you never record with a mic. An open-back pair suits that better.

On a tight budget?

The Audio-Technica ATH-M20x in our starter stack is a closed-back pair for recording and a first mix. Move up to one of the picks above once you start mixing seriously.

What else you need

How we tested

We haven't mixed on these headphones yet. This guide compares the makers' own specs (Sennheiser, beyerdynamic and Audio-Technica product pages and spec sheets), focused on what matters for mixing at home: open or closed design, impedance and whether a typical interface can drive it, weight, cables and replaceable parts. We also read long-term owner reports. We don't describe how any pair sounds until we've used it on real mixes. When we have, we'll add our notes and update the picks if needed.

Frequently asked questions

Q1Should I mix on open-back or closed-back headphones?

Open-backs are usually preferred for mixing. They don't build up pressure inside a sealed cup, and people often describe them as sounding more open and speaker-like. Closed-backs are better for recording, because they don't leak into the mic. If you can only buy one pair and you also record, closed-back is the practical choice.

Q2Can my audio interface drive 300-ohm headphones?

It depends on the interface's headphone output. High-impedance headphones need more voltage to get loud enough. Check the interface's spec sheet for headphone output power or a recommended impedance range, or pick a lower-impedance pair like the beyerdynamic DT 900 PRO X (48 ohms) or ATH-M50x (38 ohms).

Q3Can you mix a whole song on headphones?

Yes, and lots of home producers do, especially in untreated rooms. Check the mix on other systems (monitors, earbuds, a car) before you call it done, because headphones present stereo differently from speakers.

Q4Do I need a headphone amp for mixing?

Only if your interface can't get your headphones loud enough without turning the volume close to maximum. That's most likely with high-impedance models like the HD 600 (300 ohms) or ATH-R70xa (470 ohms).

Q5Are open-back headphones good for recording vocals?

No. Open-backs leak the backing track, and a sensitive mic picks it up. Wear closed-backs while you track. Our open-back vs closed-back guide explains why.